How to Make Bias Tape: Continuous and Strip Methods

Quick answer: Cut fabric strips at 45 degrees to the grain. The length of a square's worth of continuous bias is its side squared divided by the strip width; a 2 in strip needs a 23 in square for 250 in. Fold the edges to the middle and press.

Sewing gear on Amazon

Sponsored

As an Amazon Associate, Sewing Insider earns from qualifying purchases. See our affiliate disclosure.

Prices and availability were accurate when retrieved from Amazon and may change. Retrieved Nov 18, 2026.

Continuous bias from a square

Bias is a strip cut at 45 degrees to the threads. It stretches along its length, which is why it curves around necklines and armholes. The continuous method turns a square into one long strip with no joins to sew. To work out the square size, use the bias tape calculator.

  1. Cut the square in half

    Fold the square corner to corner and cut along the fold to get two triangles.

  2. Join the triangles

    Lay them with equal overhangs, sew the straight edge and press the seam open.

  3. Mark the lines

    Draw parallel lines at your strip width across the fabric. Honeybear Lane draws them about 4 in apart for wide strips; use your own strip width.

  4. Form the tube

    Fold into a tube, matching the lines but offset by one strip so the first column meets nothing. Sew, press open.

  5. Cut along the line

    Start at the offset and follow the line round. You cut one long strip.

  6. Fold and press

    Fold the strip in half, then fold the raw edges to the middle crease and press.

cut at 45 degreesjoin the stripsend to end
A square becomes one strip, or a few strips are joined end to end.

How much strip does a square give?

A square's area is its side times its side. A strip of width w covers an area of length times w, so the length is the side squared divided by the strip width. Running it backwards gives the square needed for a length: the square root of (length times width), rounded up. A little is lost at each end and when the pieces are joined, so Sew4Home adds 2 to 3 in to the square for seaming.

Strip widthSquareStrip length (about)
1 in18 in324 in
2 in18 in162 in
2 in23 in264 in
2 1/2 in23 in212 in

Computed: side × side ÷ strip width; before joining losses. Honeybear Lane: continuous bias binding, Sew4Home: bias binding basics (single source for the rule).

Cut width for the finished tape

For single-fold binding, Sew4Home doubles the visible edge and adds seam allowances: with a 1/2 in finished edge, cut 2 in. For double-fold binding, start with the seam allowance, double it, then add four times the finished edge. Their example uses a 1/2 in seam allowance and a 1/2 in reveal for 3 in strips.

If you only need a short length, cut separate strips on the bias, place two strips right sides together at right angles, sew them with a 1/4 in seam (small points will show beyond the edges), trim the points and press the seams open. Fold and press as above. A bias tape maker feeds the strip through while you press, which gives even folds.

Using it

Pin or clip the tape over the raw edge and stitch it down close to the fold. Ease the tape round curves and do not pull it, because bias stretches and can pucker. For a pillow edge, piping or a quilt, see our guides to quilt binding and the yardage calculator.

Frequently asked questions

How do I make bias binding from a square of fabric?

Cut the square in half corner to corner, join the triangles, mark parallel lines at the strip width, sew into a tube offset by one strip and cut along the line.

What is bias tape used for?

It finishes raw edges, binds quilts and necklines, and makes piping and ties. Because it is cut on the bias it stretches enough to follow curves.

Can you make bias tape at home?

Yes, with a square of fabric, a ruler, a cutter and an iron. A bias tape maker is optional.

Is it cheaper to make your own bias tape?

It depends on the fabric you use. The advantage is matching your project, not always cost, and a small piece of fabric makes a long tape.

What we checked, and where

Show what we checked and the sources
What we stateSource and status
Length = side² ÷ strip widthSingle source (Honeybear Lane); the same square-root rule appears in Sew4Home.
Continuous method stepsHoneybear Lane.
Cut widths for single and double fold; strip joinSew4Home.

Date checked: November 17, 2026. A claim with one readable source is labelled single source; formulas are computed.

This article reflects independent editorial research and disclosed buying criteria, not hands-on testing. Sewing machines vary by model, so always check your machine's manual for exact setup, threading, and safety guidance. This is not professional repair, electrical, or safety advice. Some links on this page are Amazon Associates affiliate links; see our affiliate disclosure.