Quilt Binding Calculator: Strips and Yardage

Quick answer: Add up all four sides, add 10 in for corners and the final join, divide by 40 and round up: that is the number of strips. A 60 × 80 in quilt needs 8 strips cut 2½ in wide, which is ⅝ yd of fabric.

Quilt Binding Calculator

Units
Fine-tune options (1)

extra for corners and the final join

10 to 12 in.

Fractions work: type 2 1/4 or 2.25, or tap a fraction under the box.

8 strips cut 2½ in wide, across the fabric width

Buy ⅝ yd (0.57 m) of fabric.

The working
Around the quilt
280 in
Plus extra
10 in
Binding needed
290 in

Each strip counts as 40 in after the seams that join strips end to end.

all four edges280 in around 60 in

Sewing gear on Amazon

Sponsored

As an Amazon Associate, Sewing Insider earns from qualifying purchases. See our affiliate disclosure.

Prices and availability were accurate when retrieved from Amazon and may change. Retrieved Nov 17, 2026.

How it works

  1. Add up the edges

    Twice the width plus twice the length gives the distance round the quilt.

  2. Add the extra

    Corners, the seams that join strips and the final overlap all use fabric. Sources say 10 in; use 12 if you like more room.

  3. Divide into strips

    Each strip counts as 40 in after it is joined to the next. Round up, then multiply by the strip width.

Why 40 inches per strip

A strip cut across 44 in cotton is nominally 44 in long, but the selvedge ends are trimmed and each diagonal join uses up about one strip width. Two quilting references both count 40 in per strip, so the tool does too. If you buy slightly more than it says you will rarely regret it; buying less leaves a seam in the wrong place on the last side.

Traditional binding is cut 2¼ in wide and a lot of quilters now prefer 2½ in for a thicker quilt sandwich. Wider strips use more fabric, so pick the width before you shop.

The yardage is rounded up to the next ⅛ yd. For the 60 × 80 in example that is 8 strips × 2½ in = 20 in of fabric, bought as ⅝ yd.

Binding by quilt size

QuiltAround the edge2¼ in strips2½ in strips
Crib / baby 36 × 52 in176 in5 strips, ⅜ yd5 strips, ⅜ yd
Throw / lap 50 × 65 in230 in6 strips, ⅜ yd6 strips, ½ yd
Twin 68 × 86 in308 in8 strips, ½ yd8 strips, ⅝ yd
Full 84 × 90 in348 in9 strips, ⅝ yd9 strips, ⅝ yd
Queen 90 × 95 in370 in10 strips, ⅝ yd10 strips, ¾ yd
King 108 × 95 in406 in11 strips, ¾ yd11 strips, ⅞ yd

Computed: 10 in extra, 40 in per strip, yardage rounded up to ⅛ yd.

Frequently asked questions

How many binding strips for a throw quilt?

A throw of about 50 × 65 in has a 230 in perimeter. With a 10 in tail that is 240 in of binding, so 6 strips cut 2½ in wide.

What width should I cut quilt binding?

Two to two and a half inches. 2¼ in is the traditional width; 2½ in gives a thicker, easier to handle binding on a quilt with thick batting.

Do I need bias binding?

Not for a straight-edged quilt. Strips cut straight across the fabric work fine; bias strips are for curved edges and use more fabric.

What we checked, and where

RuleSource and status
Strip width 2¼ or 2½ in, 40 in usable per stripUtah State University Extension and the National Quilters Circle.
10 in added to the perimeterUtah State University Extension. A 12 in tail is common but is not on a second readable page, so it is a single source.
Yardage rounded up to ⅛ ydNational Quilters Circle.

Date checked: November 17, 2026. Formulas are labelled computed; a rule with one source is labelled single source.

These calculators give planning figures: check them against your pattern and your fabric. Some links on this page are Amazon affiliate links; see our affiliate disclosure.