Bias Tape Calculator: Continuous Bias from a Square

Quick answer: Length = side × side ÷ strip width. An 18 in square cut into 2 in strips makes about 162 in of bias strip, before joining.

Bias Tape Calculator

Units
Calculate
Cut width, not the width of the finished tape.

Fractions work: type 2 1/4 or 2.25, or tap a fraction under the box.

About 162 in (411.5 cm) of continuous bias strip

The working
Square
18 in
Strip width
2 in

Length = side × side ÷ strip width, before joining. Cutting loses a little at each end.

18 in squarestrips 2 in wide, cut at 45°

Sewing gear on Amazon

Sponsored

As an Amazon Associate, Sewing Insider earns from qualifying purchases. See our affiliate disclosure.

Prices and availability were accurate when retrieved from Amazon and may change. Retrieved Nov 17, 2026.

How it works

  1. Choose the direction

    Start with a square and find the length, or start with the length and find the square.

  2. Enter the strip width

    This is the width you cut, which is wider than the finished tape.

  3. Cut and join

    Cut the square on the diagonal, join the pieces to a tube with a step, then cut round and round.

Why a square makes so much strip

A square of fabric is a fixed area. A strip of width w has area length × w, so the length of strip is the area divided by w: side × side ÷ w. That is the same rule as the one in this calculator. It ignores the small amount lost at each end and where the pieces are joined, so leave a few inches spare.

Running the sum backward gives the square needed for a length: side = √(length × width), rounded up to the next ⅛ in. For 120 in of 2 in strip that is a 15½ in square.

One tutorial cuts the square in half first and doubles the side in its sum, and the answer is the same in the end; the calculator uses the plain square rule, so do not mix the two. This rule has one source we could read, which is why the page says so.

Continuous bias from a square

Square1½ in strips2 in strips2½ in strips
12 in96 in (2¾ yd)72 in (2 yd)58 in (1⅝ yd)
18 in216 in (6 yd)162 in (4½ yd)130 in (3⅝ yd)
24 in384 in (10¾ yd)288 in (8 yd)230 in (6½ yd)
30 in600 in (16¾ yd)450 in (12½ yd)360 in (10 yd)
36 in864 in (24 yd)648 in (18 yd)518 in (14½ yd)

Computed: side × side ÷ strip width, before joining. Single source for the rule.

Frequently asked questions

How much bias tape does a square make?

Divide the area by the strip width: an 18 in square cut into 2 in strips makes about 162 in.

What size square do I need for 5 yards of bias?

5 yd is 180 in. With 2 in strips, √(180 × 2) = 19 in, so cut a 19 in square.

How wide should I cut bias strips?

Wider than the finished tape. The cut width equals twice the seam allowance plus four times the finished width that shows, per one source.

Is bias tape cut on the bias?

Yes. Strips cut at 45 degrees to the weave stretch, so they curve smoothly round necklines and quilt edges.

What we checked, and where

RuleSource and status
Length = side² ÷ strip widthSingle source (Honeybear Lane).
Cut width = 2 × seam allowance + 4 × finished revealSingle source (Sew4Home), for double-fold binding.

Date checked: November 17, 2026. Formulas are labelled computed; a rule with one source is labelled single source.

These calculators give planning figures: check them against your pattern and your fabric. Some links on this page are Amazon affiliate links; see our affiliate disclosure.