How to Wind and Thread a Bobbin

Quick answer: Wind the bobbin evenly at a medium speed to about 80 to 90 percent full, then load it as your machine shows: dropped in under a cover plate (top-loading) or in a removable case from the front. Thread direction varies, so follow the diagram on your machine.

Sewing gear on Amazon

Sponsored

As an Amazon Associate, Sewing Insider earns from qualifying purchases. See our affiliate disclosure.

Prices and availability were accurate when retrieved from Amazon and may change. Retrieved Nov 18, 2026.

Winding the bobbin

This page is about the bobbin only. For the upper thread path, see how to thread a sewing machine.

  1. Set up the thread

    Put the spool on the pin and follow the bobbin-winding path marked on your machine (it differs from the sewing path). Pass the thread through the bobbin tension guide.

  2. Anchor it

    Thread through the small hole in the bobbin from the inside out, and push the bobbin onto the winder spindle.

  3. Wind at medium speed

    Hold the thread tail and start slowly. Fast winding can make loose, uneven layers that cause tension problems later.

  4. Stop at 80 to 90 percent

    An overfilled bobbin can jam in the case or wind unevenly (SewGuide). Cut the thread and remove it.

Loading it: top-loading or front-loading

Look at where the bobbin goes. If there is a small cover plate in front of the needle, it is top-loading. If you open a door on the front or pull out a metal case, it is front-loading.

top-loading (drop-in)front-loading (case)seen from aboveseen from the front
Two systems; the machine's manual diagram is the final word.
Top-loading (drop-in)Front-loading (case)
WhereUnder a cover plate by the needleBehind a door at the front of the machine
Bobbin typeUsually plastic onlyOften metal, in a separate removable case
LoadingPlace it as the printed diagram shows; the thread usually runs anticlockwise but check; pull the thread through the slitDrop the bobbin in the case, thread through the tension spring, leave 8 to 10 cm of tail, push the case in until it clicks
Bring the thread upTurn the handwheel toward you once to catch the bobbin threadSame

SewGuide: winding and loading bobbins (single source). Thread direction differs by machine and by source, so your manual overrules this table.

After loading, hold both thread tails and pull them gently to the back before you start sewing.

Check the tension

With a front-loading case out of the machine and the thread hanging, give it a small jerk. SewGuide's test: if the case hangs and drops slightly, the tension is about right. If it drops freely it is too loose, and if it does not move at all it may be too tight. Do not adjust the screw unless you have a spare case, because it is easy to overdo it.

If stitches still loop or pull after the bobbin is correct, see tension troubleshooting.

Common bobbin problems

What you seeLikely causeTry
Bobbin thread loops or bunchesBobbin not seated, or thread not through the tension springRemove, re-load following the diagram
Uneven or loose bobbin windingWound too fast or off the tension guideRe-wind slowly through the guide
Bobbin will not fit or jamsWrong bobbin type or overfullUse the bobbin type in your manual; wind less thread

Our suggestions, consistent with the SewGuide page; not a sourced chart.

Frequently asked questions

How do I thread a bobbin?

Wind it evenly, then load it as your machine shows. Top-loading machines drop it in under a cover plate; front-loading machines use a removable case with a tension spring.

How do I thread a bobbin on a Singer?

It depends on the model: many classics use a front-loading case and many current models use a drop-in bobbin. Follow the diagram printed on the machine or in the manual.

What does a correctly threaded bobbin look like?

The thread unwinds in the direction your machine shows, passes under the tension spring or through the slit, and pulls with slight resistance. Both thread tails lie to the back.

How do I wind a bobbin?

Follow the winding path, thread the bobbin from the inside, run the winder at a medium speed and stop around 80 to 90 percent full.

What we checked, and where

Show what we checked and the sources
What we stateSource and status
Wind evenly, medium speed, stop at 80 to 90 percent fullSewGuide (single source).
Drop-in vs front-loading differences and the drop testSewGuide; thread direction varies by machine, check the manual.
Switch off before needle-area workBrother Solutions Center (single readable maker source).

Date checked: November 17, 2026. A claim with one readable source is labelled single source; formulas are computed.

This article reflects independent editorial research and disclosed buying criteria, not hands-on testing. Sewing machines vary by model, so always check your machine's manual for exact setup, threading, and safety guidance. This is not professional repair, electrical, or safety advice. Some links on this page are Amazon Associates affiliate links; see our affiliate disclosure.