How to Sew a Buttonhole by Machine

Quick answer: Interface the area, measure the button, and make a test buttonhole on scrap. Length is the button's width plus its thickness, or half the button's circumference plus 1/8 in. Cut it open from the centre, with a pin across each end.

Sewing gear on Amazon

Sponsored

As an Amazon Associate, Sewing Insider earns from qualifying purchases. See our affiliate disclosure.

Prices and availability were accurate when retrieved from Amazon and may change. Retrieved Nov 18, 2026.

Sew a buttonhole in six steps

This guide is for plain, firm fabric with a machine buttonhole foot. For slippery fabrics such as rayon or satin, see buttonholes on slippery fabrics.

  1. Interface and mark

    Interface the button and buttonhole areas, even if the pattern does not say so (Sewing.org and NMSU). Mark the position and length.

  2. Measure the button

    Add the button's width and its thickness, or wrap tape round it, halve that and add 1/8 in.

  3. Fit the buttonhole foot

    Use the buttonhole foot instead of the standard foot for more even sizing (NMSU).

  4. Sew a test

    Make one on a scrap with the same layers, cut it open and try the button.

  5. Sew the real one

    Follow the machine's automatic cycle, or turn the dial through the four stages on a 4-step machine.

  6. Cut it open

    Put a pin across each end, then cut from the centre toward the ends.

button widthbuttonhole: width + thickness
Button width plus thickness gives the buttonhole length.

How long to make it

RuleHowExample
Width plus thicknessMeasure the button across and add how thick it is7/8 in button, 1/8 in thick: 1 in
Circumference methodWrap tape round the widest part, halve, add 1/8 in2 3/4 in around: 1 3/8 + 1/8 = 1 1/2 in
Test sampleCut a slit in a scrap and try the buttonLengthen until it slides through easily

Sewing.org: buttonholes, NMSU Extension: machine buttonholes made easy. The two sources give two different methods; treat the result as an estimate and test. Very thick or domed buttons may need a longer hole.

The button size chart converts ligne to millimetres and lists lengths for common button widths.

One-step or four-step machines

Some machines sew an automatic buttonhole in one step: you set the length and the machine sews both sides and the end bars. Others need the dial changed manually to move through the stages, which NMSU says to check in your manual if you are new. A good machine buttonhole has stitches close together like a satin stitch, with lips just a thread apart so they do not fray when cut (Sewing.org). For a stronger hole, stitch round a second time.

Cutting it open without a mistake

Use a razor, a buttonhole cutter or small sharp scissors, starting at the centre and cutting toward each end. Before cutting, Sewing.org runs the point of scissors or a seam ripper between the lips to separate the threads. A straight pin across each end stops the cutter going too far. NMSU's advice is to err on the small side, test the button, and enlarge only as needed.

For home projects such as curtains, where interfacing is not practical, NMSU suggests tear-away stabilizer above and below while stitching.

Frequently asked questions

How do you stitch a buttonhole step by step?

Interface, mark, fit the buttonhole foot, sew a test on a scrap, sew the real one, then cut it open from the centre with a pin at each end.

How long should a buttonhole be?

The button's width plus its thickness, or half the button's circumference plus 1/8 in. Sew a test on scrap and adjust.

How do I use the buttonhole foot on a Brother machine?

Attach the buttonhole foot and follow your model's manual, because the steps and the way the length is set vary by machine. Test on a scrap first.

What is the easiest way to cut a buttonhole open?

Pins across both ends, then cut from the centre outward with a seam ripper, a buttonhole cutter or sharp small scissors.

What we checked, and where

Show what we checked and the sources
What we stateSource and status
Length = width + thickness; or half the circumference + 1/8 inTwo sources, two methods (Sewing.org; NMSU): an estimate, test on scrap.
Interface both the button and buttonhole areasSewing.org and NMSU.
Cut open from the centre with pins at the endsSewing.org and NMSU.

Date checked: November 17, 2026. A claim with one readable source is labelled single source; formulas are computed.

This article reflects independent editorial research and disclosed buying criteria, not hands-on testing. Sewing machines vary by model, so always check your machine's manual for exact setup, threading, and safety guidance. This is not professional repair, electrical, or safety advice. Some links on this page are Amazon Associates affiliate links; see our affiliate disclosure.