How to Hem Pants by Hand or Machine

Quick answer: Mark the length with the pants and shoes you will wear, turn the extra to the inside, press, and hold it with a hand blind stitch, fusible web or a machine topstitch. NMSU Extension gives 1 to 2 in as the hem depth for pants.

Scissors cutting black fabric beside a yellow measuring tape
Photo: Los Muertos Crew on Pexels

Sewing gear on Amazon

Sponsored

As an Amazon Associate, Sewing Insider earns from qualifying purchases. See our affiliate disclosure.

Prices and availability were accurate when retrieved from Amazon and may change. Retrieved Nov 18, 2026.

Hem pants in five steps

The method changes with the fabric, but the order never does: mark, trim, press, secure, press again. If you only want to shorten denim and keep the factory hem, use the jeans hem guide; this page covers trousers and any pants with a plain hem.

  1. Mark the length

    Wear the shoes you will wear with them. Have someone else mark the hemline while you stand still, folding the leg up and pinning.

  2. Allow for the hem

    Pants and blouses usually take a hem 1 to 2 in deep (NMSU Extension). Mark that depth below the new edge and trim the rest.

  3. Press the fold

    Press the new fold with steam for a sharp edge. Do not press over pins.

  4. Secure the hem

    Choose a method from the table below: hand blind stitch, fusible web or machine stitch.

  5. Press and check

    Press again from the wrong side, try the pants on, and check the length from the side and back.

blind stitch (hand)fusible webtopstitched
Three ways to hold the hem; the fabric decides.

Three hem methods compared

MethodBest forHow it worksWatch for
Hand blind stitchDress trousers, wool, lined pantsSmall horizontal stitches between the garment and the hem; no stitches show on the right sideSlow, but invisible
Fusible webLight to medium fabricsWeb strips 3/4 to 1 in wide (2 in on heavier fabric) melt between the layersNot for sheer or lace; keep it 1/4 in from the cut edge; test first
Machine topstitchCasual pants, knitsTrim the allowance to 5/8 in, then stitch 1/2 in and 3/8 in from the edgeVisible stitching; use a stretch stitch on knits

Methods and measurements: NMSU Extension: Making Perfect Garment Hems. A machine blind hem, which the same page suggests for children's clothes and sturdy sportswear, needs a blind-hem foot or stitch and a practice sample.

Whichever you choose, finish the raw edge first if the fabric frays. A zigzag or serged edge is quicker than turning the edge under, and the hem can then be let down later if you trim the seam allowances only moderately.

How deep should the hem be?

GarmentHem depth
Pants, jackets, blouses1 to 2 in (NMSU Extension)
Skirts, dresses, coats2 to 3 in (NMSU) or 1 1/2 to 2 in (BellaOnline)
Flared or circular edges1/2 to 1 in (NMSU)

Date checked 2026-11-17. NMSU Extension: Making Perfect Garment Hems, BellaOnline: basics of hemming. The two pages overlap on skirts only and differ there, so the pants figure is single source.

For tapered pants, a deep hem will not lie flat because the leg gets narrower toward the hem. Keep the hem shallow or fuse it. For a cuff, add twice the cuff width plus the hem.

Mistakes that spoil a hem

Marking the length without shoes on is the most common one. A new garment, especially one cut on the bias, can drop as it hangs, so NMSU Extension suggests letting it hang for 24 hours before you mark. Trimming the seam allowances inside the hem too narrow means the pants cannot be let down again.

A hem that looks puckered on the right side usually has stitches pulled too tight, so keep the thread relaxed and the stitches small. Try the pants on again after pressing: a hem pressed without a break at the fold can look shorter than it is.

Frequently asked questions

What is the easiest way to hem pants?

Fusible web is the quickest on light to medium fabrics: press the hem, lay a strip between the layers and fuse it. A machine topstitch is the next easiest. Test either on a scrap first.

How do I hem pants without a sewing machine?

Use a hand blind stitch: small horizontal stitches between the garment and the hem so nothing shows on the right side. Fusible web also needs only an iron.

What is the best length to hem pants?

That is personal, but mark with the shoes you will wear and the pants on. The hem depth itself is 1 to 2 in for pants, per NMSU Extension.

How do I fix pants that are too long?

Turn up the extra length to the inside, press, and secure it with a hand blind stitch, fusible web or topstitching. Trim the excess to the hem depth first.

What we checked, and where

Show what we checked and the sources
What we stateSource and status
Pants hem depth 1 to 2 in; skirts 2 to 3 in; flared 1/2 to 1 inNMSU Extension; BellaOnline differs on skirts (1 1/2 to 2 in).
Fusible web strip widths and the 1/4 in setback; topstitched hem 5/8 in trim, stitch at 1/2 and 3/8 inNMSU Extension (single source).
Let a new garment hang 24 hours before markingNMSU Extension.

Date checked: November 17, 2026. A claim with one readable source is labelled single source; formulas are computed.

This article reflects independent editorial research and disclosed buying criteria, not hands-on testing. Sewing machines vary by model, so always check your machine's manual for exact setup, threading, and safety guidance. This is not professional repair, electrical, or safety advice. Some links on this page are Amazon Associates affiliate links; see our affiliate disclosure.